Static Routing with Alcatel-Lucent Service Routers - www.ipcisco.com : www.ipcisco.com
You can Reach Our "CCNA Lab Courses with Packet Tracer" on Udemy.!!!
cisco-packet-tracer-ccna-adventure-1- cisco-packet-tracer-ccna-adventure-2-
Content Protection by DMCA.com

Static Routing with

Alcatel-Lucent Service Routers


As you know Alcatel-Lucent is another network device vendor like Cisco and Juniper. Here, we will see the static route configuration with Alcatel-Lucent routers. For this configuration, we will use one of the routers in Alcatel-Lucent’s Service Router family, 7750 SR-C4.

The topology that we will use is below.



Beside these addresses on the picture, we will use system addresses for each router. This system addresses are below:

R1 10.10.10.1
R2 10.10.10.2
R3 10.10.10.3
R4 10.10.10.4
R5 10.10.10.5
R6 10.10.10.6


Let’s start with configuring the system addresses. The configuration on one of the router is given below.

A:SR 1# configure router interface “system”
A:SR 1>config>router>if# address 10.10.10.1/32
After system address configuration, now we will configure the physical interfaces.The interface configuraiton of SR 1 is given below.

A:SR 1# configure router interface R1toR2
A:SR 1>config>router>if$ address 10.1.2.1/27
A:SR 1>config>router>if$ port 1/1/1
A:SR 1>config>router>if$ back
A:SR 1>config>router# interface R1toR3
A:SR 1>config>router>if$ port 1/1/3
A:SR 1>config>router>if$ address 10.1.3.1/27
A:SR 1>config>router>if$ back
A:SR 1>config>router# interface R1toR5
A:SR 1>config>router>if$ port 1/1/4
A:SR 1>config>router>if$ address 10.1.5.1/27

The above configuration must be done for all routers with their own address values. After the end of this configuration, you can verify the interface addresses with the “show router interface” commands.

After, interface configuration and verification for all the routers, it is time to configure statci routing. To do this, use the below commands:

SR 1
A:SR 1# configure router static-route 10.10.10.2/32 next-hop 10.1.2.2
A:SR 1# configure router static-route 10.10.10.3/32 next-hop 10.1.3.3
A:SR 1# configure router static-route 10.10.10.5/32 next-hop 10.1.5.5

SR 2
A:SR 2# configure router static-route 10.10.10.1/32 next-hop 10.1.2.1
A:SR 2# configure router static-route 10.10.10.4/32 next-hop 10.2.4.4
A:SR 2# configure router static-route 10.10.10.6/32 next-hop 10.2.6.6

SR 3
A:SR 3# configure router static-route 10.10.10.1/32 next-hop 10.1.3.1
A:SR 3# configure router static-route 10.10.10.4/32 next-hop 10.3.4.4

SR 4
A:SR 4# configure router static-route 10.10.10.2/32 next-hop 10.2.4.2
A:SR 4# configure router static-route 10.10.10.3/32 next-hop 10.3.4.3

To verify the routes that we configure use the below “show router route-table” command.

Now we can ping the directly connected interfaces from R1 or from other routers. But when we ping R4 from R4(not directly connected), the ping will fail.Because there is no static route defined for R1 to R4. Let’s do it and after that check the connection with ping from R1 to R4.

Firstly configure the static route from R1 to R4. After that configure the reverse route from R4 to R1.

SR 1
A:SR 1# configure router static-route 10.10.10.4/32 next-hop 10.1.2.2

SR 4
A:SR 4# configure router static-route 10.10.10.1/32 next-hop 10.2.4.2


After this configuration you will see that pinging from R1 to R4 is sucessful.
I hope this first article about Alcatel-Lucent Service Routers will be useful for you… For more configuration on Alcatel-Lucent Service Routers keep on…;)

You can also read how to configure Default Routes and Floating Static Routes on Alcatel-Lucent Routers.

You can reach the Static Route Configurations on Other Vendor Routers below:

Static Route Configuration on Juniper Routers
Static Route Configuration on Cisco Routers
Static Routing Configuration on Alcatel-Lucent Routers

Youn can join OUR Facebook Group with the below links!!!

You can Reach Our "CCNA Lab Courses with Packet Tracer" on Udemy.!!!
cisco-packet-tracer-ccna-adventure-1- cisco-packet-tracer-ccna-adventure-2-



About the Author
Gokhan Kosem is a telecommunation and network engineer. His ambition to IP networks and end-to-end system installation made him to prepare this web-site. By sharing his experiences about various networking protocols beside different system installation experiences and Cisco, Juniper, Alcatel-Lucent devices configurations, he is aimed to be helpful for his collegues in all over the world. He is currently lives in Istanbul, Turkey.

2 comments for “Static Routing with Alcatel-Lucent Service Routers”

1
Beheşti

elinize sağlık :)

July 18th, 2013 at 14:34
2
samad

very helpful, thank you .

February 7th, 2014 at 01:21

Leave a Reply


Copy Protected by Chetan's WP-Copyprotect.