JNCIP Quiz 2 ⋆ IpCisco

JNCIP QUIZ 2

Please wait while the activity loads.
If this activity does not load, try refreshing your browser. Also, this page requires javascript. Please visit using a browser with javascript enabled.

If loading fails, click here to try again

CONGRATULATIONS!

YOU HAVE COMPLETED JNCIP QUIZ 2.

YOU HAVE %%SCORE%% TRUE ANSWERS OUT OF %%TOTAL%% QUESTIONS.

YOUR SCORE IS %%PERCENTAGE%%.

%%RATING%%

Your answers are highlighted below.

Question 1

STP .... State is the state that MAC Table is filled with the learned addresses.

A	Listenning
B	Established
C	Blocked
D	Learning
E	Full

Question 2

There are two types RSVP-signaled LSPs. Which ones are True about them?

A	Explicit-path LSPs : Hops of LSP are computed automatically.
B	Constrained-path LSPs : Hops of LSP are computed automatically.
C	Constrained-path LSPs : Hops of the LSP are configured manually .
D	Explicit-path LSPs : Hops of the LSP are configured manually .

Question 3

How can we display the aggregated interfaces on JUNOS?

A	show interfaces lag
B	show interfaces detail
C	show interfaces link-aggregation
D	show interfaces ae0
E	show interfaces aggregated

Question 4

How can we check the configured static routes on a Juniper router?

A	show routing-options
B	show routing-protocols
C	show routing
D	show protocol-options
E	show route-options

Question 5

What is True for many-to-many multicast applications?

A	Full mesh topology is used
B	More complex than one-to-one model
C	Receivers are known
D	All of them
E	All devices are both sources and receivers

Question 6

To use show commands in the configuration mode, .... keyword is prepended to the show command.

A	run
B	show
C	set
D	display
E	more

Question 7

If the DR Priorities are same, according to which criteria, DR election is done in a Multicast domain?

A	Highest MAC
B	Highest IP
C	Lowest Cost
D	Lowest IP
E	Lowest MAC

Question 8

RSVP ..... are used to send labels through upstream direction.

A	Session Messages
B	RESV Messages
C	PATH Messages
D	Notify Messages
E	Hello Messages

Question 9

Which one is a IPv6 Multicat Address?

A	FEC0::FF:FFF
B	FF02::5
C	FEC0::FF:001
D	2001::123
E	3001::FF:FFF

Question 10

How can we check IS-IS interfaces?

A	show router isis neighbors
B	show isis interface
C	show router isis brief
D	show router isis interface
E	show isis peers

Question 11

In Layer 3 VPN, to determine the final egress PE device for customer routes in a particular VRF, .... are used.

A	ARP Records
B	MPBGP Tables
C	Route Targets
D	Route Distinguisher
E	VRP Tables

Question 12

What is the equivalent of IPv6 address 2003:3700:0025:0000:0000:0000:0000:0005?

A	2003:37:0:25:0000:0000:0000:0000:0005
B	2003:3700::25::5
C	2003:3700:25::5
D	2003:37::25:0:0:0:0:5
E	2003:37::25:0000:0000:0000:0000:0005

Question 13

With ..... , the traffic is controlled and if the traffic close to the traffic exceed, it uses queues and made some of the traffic buffered without any drop action.

A	Traffic Marking
B	Traffic Policing
C	Traffic Caching
D	Traffic Shaping
E	Traffic Classification

Question 14

If you set your OSPF router's priority to ..., it is never selected as DR.

A	0
B	1
C	255
D	10
E	100

Question 15

Multicast Routing Protocol Signalling direction is ...., and Multicast Flow direction is ....,

A	From Receiver to RP/ From RP to Receiver
B	From Receiver to Source / From Source to Receiver
C	From Source to DR / From DR to Source
D	From Source to RP / From RP to Source
E	From Source to Receiver / From Receiver to Source

Question 16

LDP Hellos use .... multicast address.

A	224.0.0.13
B	224.0.0.22
C	224.0.0.16
D	224.0.0.1
E	224.0.0.2

Question 17

How can we configure BGP COnfederation with 67500 with members 67501 and 67502?

A	set confederation members 67501
B	All of them
C	set confederation members 67502
D	set confederation 67500
E	edit routing-options

Question 18

In MPLS Network, At the last Edge LSR, label is removed. This process is called ....

A	push
B	php
C	pop
D	swap
E	none of them

Question 19

How can we see our OSPF neighbors on Juniper routers?

A	show ospf neighbor
B	show ospf peer details
C	show ospf peers
D	show ospf details
E	show ospf neighbor details

Question 20

How can we check TCP connections on our Juniper router?

A	show system tcp
B	show protocol connections
C	show protocol tcp
D	show system connections
E	show system statistics

Once you are finished, click the button below. Any items you have not completed will be marked incorrect. Get Results

There are 20 questions to complete.

JNCIP Quiz 2

JNCIP QUIZ 2

Latest Lessons

Latest Blog Posts

WHAT YOU WILL FIND?

COURSES

SPECIALS

MEMBERSHIP