CCNP ENCOR Training is the required Core Training for CCNP 350-401 ENCOR, Enterprise Certification and CCIE Enterprise Infrastructure Certification. It is the second step after entering Cisco Networking with CCNA. CCNP Enterprise is the the most close certification path to old CCNP Routing and Switching. Beside many similar parts, there are also some additional lessons related with Enterprise Networks. In this course, we will cover all the required lessons one by one.
In CCNP Training, you will learn required Architecture, Virtualization, Infrastructure, Network Assurance, Security and Automation for Enterprise Networks.
After completing CCNP 350-401 ENCOR Training, you can pass 350-401 ENCOR Exam! After this step, you should also finish a Specialist Training of CCNP Enterprise. If you also pass one of the Specialist Exam, you will be CCNP!
What Will You Learn in CCNP ENCOR Training ? We will cover all the lessons below in this training:
- Enterprise Network Design Principles,
- WLAN Design Principles,
- Cisco SD-WAN Solution,
- Cisco SD-Access solution,
- Quality of Service,
- Switching Mechanisms,
- Device Virtualization Technologies,
- Data Path Virtualization Technologies,
- Network Virtualization Concepts,
- Layer 2, EtherChannels, VLANs, Spanning Tree
- Layer 3, OSPF, EIGRP, BGP
- Wireless Infrastructure,
- IP Services,
- Diagnostic Tools for Network Problems,
- Syslog, Netflow, SPAN, IPSLA,
- Cisco DNA Center,
- NETCONF, RESTCONF,
- Network Access Security,
- Infrastructure Security Features,
- Wireless Security Features,
- Network Security Design,
- Basic Python Scripting,
- Principles of Data Modeling,
- APIs for Cisco DNA Center and vManage,
- Other Network Automation Features.
To learn more about CCNP ENCOR, you can also visit Cisco Website. You can learn both CCNP and other certification paths here.
To Pass 350-401 ENCOR Exam at the First Attempt and Not To Lose Time , You can start our CCNP Course! This Exam is the requirement exam for both CCNP and CCIE.
Below, you can find All the Lessons of CCNP 350-401 ENCOR Training. For CCNP Enterprise and CCIE Enterprise Infrastructure Certifications, you should learn all these lessons. Most of these CCNP lessons were also the lessons of previous CCNP Routing and Swicthing. Now, the new version of these certification is CCNP Enterprise.
Modules
IPv4
Lessons
IPv6
Lessons
ICMP and ARP
Lessons
Routing Fundamentals
Lessons
RIP
Lessons
EIGRP
Lessons
OSPF
Lessons
- OSPF Virtual-Link Configuration On Packet Tracer
- LSDB (Link State Database)
- OSPF Area Border Router (ABR) and ASBR
- OSPF Cost and Shortest Path First
- OSPF NSSA and Totally NSSA on Cisco Packet Tracer
- OSPF Stub Area and Totally-Stub Area on Cisco Packet Tracer
- OSPF External Routes on Cisco Packet Tracer
- OSPF Standard Area and Backbone Area on Cisco Packet Tracer
- OSPFv3 Configuration Example on Cisco IOS
- OSPFv3 (Open Shortest Path First Version 3)
- Cisco Single Area OSPF Configuration
- Other OSPF Key Points
- OSPF Network Types
- OSPF Area Types
- OSPF LSA Types
- OSPF Packet Types
- OSPF Adjacency
- OSPF(Open Shortest Path First) Overview
BGP
Lessons
- BGP Next Hop Self Command
- BGP Multi Hop Command
- BGP Neighbor Update-Source
- Cisco eBGP Configuration on GNS3
- BGP Route Reflector
- Cisco BGP Route Reflector Configuration on GNS3
- BGP Path Attributes – MED
- BGP Path Attributes – Origin
- BGP Path Attributes – AS Path
- BGP Path Attributes – Local Preference
- BGP Path Attributes – Weight
- BGP Configuration Example on Packet Tracer
- BGP AD and BGP Path Attributes
- IBGP and EBGP
- BGP Peers, BGP Sessions, BGP Messages
- BGP (Border Gateway Protocol)
Layer 2 Technologies
Lessons
VPN Technologies
Lessons
DHCP and DNS
Lessons
EtherChannels
Lessons
NAT
Lessons
Access Lists
Lessons
Security
Lessons
SNMP
Lessons
Spanning Tree
Lessons
- PVST+ and Rapid PVST+Configuration on Packet Tracer
- PVST+ and Rapid PVST+
- MST Configuration on Cisco
- MST (Multiple Spanning Tree)
- STP Operation
- Spanning Tree Protocol
- Rapid Spanning Tree Protocol
- STP Portfast Configuration on Cisco Packet Tracer
- RSTP Configuration on Cisco Packet Tracer
- STP Configuration on Cisco Packet Tracer
VLANs
Lessons
- Inter VLAN Routing Configuration on GNS3
- Inter VLAN Routing Configuration Example
- VTP Configuration with Packet Tracer
- DTP and VLAN Frame Tagging Protocols
- Inter VLAN Routing with Router on Stick Topology
- VLANs (Virtual Local Area Networks)
- VLAN Port Assignment and VLAN Port Types
- VLAN Configuration on Cisco Packet Tracer
First Hop Redundancy
Lessons
QoS
Lessons
Port Monitor
Lessons
Path Virtualization
Lessons
Device Access Control
Lessons
Multicast Protocols
Lessons
Cisco SD-WAN
Lessons
Wireless Security
Lessons
Network Security Design
Lessons
IP Services
Lessons
Network Assurance
Lessons
Automation
Lessons
- Chef Overview
- Ansible vs Puppet vs Chef
- Ansible Overview
- Puppet Overview
- Data Serialization Languages: JSON, YAML, XML
- Network Automation Tools
- Cisco SD-Access Overview
- Traditional Network Management versus Cisco DNA Center
- Cisco DNA Center
- Cisco DNA and Intent-Based Networking (IBN)
- How Network Automation Impacts Network Management
- REST APIs Overview
Network Virtualization
Lessons
Wireless
Lessons
Other Lessons
Network Ports
MACsec (Media Access Control Security)
What is MACsec? The basic answer of what is MACsec question is this, MACsec (Media Access Control Security) is a standard based layer 2 security protocol which provides point-to-point security …
OSPF Passive Interface
What is OSPF Passive Interface and Why We Use It? Routing protocols establish neighborships with the connected routers and they talk each other about routing updates. OSPF is a Link-State …