CCNP ENCOR Quiz 9 ⋆ IpCisco

CCNP ENCOR QUIZ 9

Please wait while the activity loads.
If this activity does not load, try refreshing your browser. Also, this page requires javascript. Please visit using a browser with javascript enabled.

If loading fails, click here to try again

CONGRATULATIONS!

YOU HAVE COMPLETED CCNP ENCOR QUIZ 9.

YOU HAVE %%SCORE%% TRUE ANSWERS OUT OF %%TOTAL%% QUESTIONS.

YOUR SCORE IS %%PERCENTAGE%%.

%%RATING%%

Your answers are highlighted below.

Question 1

If we have two route to a destination with both Static Route and BGP, which one is selected?

A	BGP
B	Static
C	Both
D	None

Question 2

Which ones are some of the area types of OSPF?

A	Standard
B	All of them
C	Stub
D	NSSA
E	Backbone

Question 3

How can we set OSPF priority as 140?

A	set ospf priority 140
B	ip ospf priority 140
C	ospf priority 140
D	set priority 140 ospf
E	ip priority 140

Question 4

What is the metric of RIPng?

A	Delay
B	All of them
C	Cost
D	Bandwidth
E	Hop Count

Question 5

BGP ..... attributes may not be supported by all BGP routers.

A	Optional
B	Well-known

Question 6

Which ones are true for OSPF?

A	Default AD is 110 for Cisco
B	Do not use tables
C	Default AD is 150 for Cisco
D	Use three table
E	Use cost as metric

Question 7

How to configure variance as 3 and maximum used paths as 5 for EIGRP Load Balancing?

A	eigrp-maximum-paths 5
B	eigrp maximum-paths 5
C	eigrp-variance 3
D	Variance 3
E	Maximum-paths 5

Question 8

How can we enable OSPFv3 globally on a Cisco router?

A	ipv6 router ospf 1
B	ipv6 ospf 1
C	router ospf 1 ipv6
D	router ipv6 ospf 1
E	router ospf 1

Question 9

IPv6 multicast addresses start with .... prefix.

A	FEC0::/8
B	FF00::/8
C	2001::/8
D	FE00::/8
E	3001::/8

Question 10

In routing table, OSPF routes are indicated with ....

A	O
B	N
C	C
D	D
E	S

Question 11

To enable IPv6 on a Cisco router interface, we use ... command.

A	ipv6 run
B	ipv6 start
C	ipv6 create
D	ipv6 enable
E	ipv6

Question 12

How can we check IPv6 Routing Table?

A	show ipv6 route
B	show ip route
C	ip ipv6 route
D	ipv6 route
E	show ip ipv6 route

Question 13

By default, EIGRP uses .... and .... to calculate metric.

A	Bandwidth
B	Delay
C	Hop Count
D	Attributes
E	Extensions

Question 14

Which ones is a Distance Vector protocol?

A	BGP
B	IS-IS
C	EIGRP
D	OSPF
E	RIP

Question 15

Which ones are PIM Modes?

A	PIM-EM
B	PIM-DM
C	PIM-SM
D	PIM-SSM
E	All of them

Question 16

We have an IP prefix 172.16.200.6/20.Which of the following can be valid host IDs for this prefix?

A	172.16.210.1
B	172.16.205.1
C	172.16.190.1
D	172.16.208.1
E	172.16.209.1

Question 16 Explanation:

HostMin: 172.16.192.1 10101100.00010000.1100 0000.00000001 HostMax: 172.16.207.254 10101100.00010000.1100 1111.11111110

Question 17

Which multicast range is used privately?

A	224.0.0.0 - 224.255.255.255
B	239.0.0.0 – 239.0.0.255
C	239.0.0.0 – 239.255.255.255
D	224.0.0.0 - 224.0.0.255
E	224.0.1.0 - 238.255.255.255

Question 18

What is the administrative distance of IS-IS for Cisco?

A	120
B	90
C	110
D	100
E	115

Question 19

How to configure EIGRP with Autonomous System Number 50 and network 10.10.10.0/24 under it?

A	router eigrp 50 create
B	router eigrp 50
C	network 10.10.10.0 0.0.0.255
D	none of them
E	network 10.10.10.0 24

Question 20

Which one is an IPv6-mapped Ipv6 Address?

A	::10:10:10:1/16
B	::FFFF:10.10.10.1/96
C	::FFFF:10.10.10.1/16
D	::10:10:10:1/96
E	::0:10.10.10.1/64

Once you are finished, click the button below. Any items you have not completed will be marked incorrect. Get Results

There are 20 questions to complete.

CCNP ENCOR Quiz 9

CCNP ENCOR QUIZ 9

Latest Lessons

Latest Blog Posts

WHAT YOU WILL FIND?

COURSES

SPECIALS

MEMBERSHIP