NRS II Services Quiz 3 ⋆ IpCisco

NRS II SERVICES QUIZ 3

Please wait while the activity loads.
If this activity does not load, try refreshing your browser. Also, this page requires javascript. Please visit using a browser with javascript enabled.

If loading fails, click here to try again

CONGRATULATIONS!

YOU HAVE COMPLETED NRS II SERVICES QUIZ 3.

YOU HAVE %%SCORE%% TRUE ANSWERS OUT OF %%TOTAL%% QUESTIONS.

YOUR SCORE IS %%PERCENTAGE%%.

%%RATING%%

Your answers are highlighted below.

Question 1

Which ones are the selection criteria of mirror sources?

A	Ingress Label
B	MAC Filter
C	SAP
D	All of them
E	IP Filter
F	Port

Question 2

After Enabling MPLS, RSVP also need to be configured.

A	False
B	True

Question 2 Explanation:

If you configure MPLS, RSVP is also enabled automatically.

Question 3

How can we check the Epipe services configure on a router?

A	show service-using epipe
B	show services epipe
C	show services-using epipe
D	show service epipe usage
E	show services service-using epipe

Question 4

VPRN X's VRF is shared with all the PEs that VPRN X exist.

A	True
B	False

Question 5

How can we check the services that use SDP 30?

A	show service 30 sdp
B	show service sdp 30
C	show service 30 sdp-using
D	show service 30 sdp details
E	show service sdp-using 30

Question 6

With which protocols, the Tranfered Tunnel is formed between two PE for L2 VPNs?

A	TLDP
B	LDP
C	RSVP-TE
D	MP-BGP
E	All of them

Question 7

Which ones are true for VPLS?

A	Multipoint-to-Multipoint connection
B	Layer 2 VPN Service
C	From customer perspective it is like they connect to a Router
D	Layer 2/3 VPN Service
E	From customer perspective it is like they connect to a LAN switch

Question 8

Within the same VPN Service, Flooded traffic that come to Mesh-SDP, it sends this to

A	Spoke-SDPs
B	None of them
C	Other Mesh-SDPs
D	SAPs
E	Al of them

Question 9

For VPN Services minimum how many label is required in an MPLS packet?

A	3
B	5
C	2
D	1
E	4

Question 10

Outher Label signalling uses ...., .... or ....

A	LDP
B	MPBGP
C	TLDP
D	RSVP
E	GRE

Question 11

How can we create SDP 80 with LSP ABC_LSP towards other end 20.20.20.20?

A	configure service sdp 80 create peer 20.20.20.20 lsp ABC_LSP no shutdown
B	configure service sdp 80 mpls to 20.20.20.20 lsp ABC_LSP no shutdown
C	configure router sdp 80 mpls to 20.20.20.20 lsp ABC_LSP no shutdown
D	configure service sdp 80 mpls create far-end 20.20.20.20 lsp ABC_LSP no shutdown
E	configure service sdp 80 create peer 20.20.20.20 lsp ABC_LSP

Question 12

How can we define a Spoke SDP with SDP ID 30 and VC-ID 100?

A	configure service epipe 5 customer 10 spoke-sdp 30:100
B	configure service epipe 5 create spoke-sdp 100:30
C	configure service epipe 5 customer 10 create spoke-sdp 100:30
D	configure service epipe 5 create customer 10 create spoke-sdp 30:100
E	configure service epipe 5 customer 10 spoke-sdp 100:30

Question 13

Which one is True for IES ?

A	A customer can have only one IES
B	In a single IES one more interface van be used
C	All interfaces of an IES is one customer's
D	Different interfaces of an IES is different customer's
E	A customer can have one more IES

Question 14

How to verify Forwarding Information Base (FIB) for VPRN 250?

A	show router 250 fib 1
B	show service 250 fib active
C	show router 250 details
D	show service 250 active
E	show service 250 fib 1

Question 15

If we set a port with Dot1q encapsulation, it supports ... service(s) on it.

A	One
B	Infinite
C	Two
D	Zero
E	Multiple

Question 16

An IES can terminate Spoke-SDP not Mesh-SDP.

A	True
B	False

Question 17

What is the direct Internet Access service of Nokia?

A	VPRN
B	IES
C	VPWS
D	Epipe
E	VPLS

Question 18

How can we configure a VPRN Service 250 with Customer 25? (Router ID=1.1.1.1)

A	configure router vprn 250 customer 25 create system-id 1.1.1.1
B	configure service vprn 250 customer 25 router-id 1.1.1.1
C	configure router vprn 250 customer 25 router-id 1.1.1.1
D	configure service vprn 250 customer 25 create system-id 1.1.1.1
E	configure service vprn 250 create customer 25 create router-id 1.1.1.1

Question 19

If SP Network is IPv4, the next hop of the advertising 6VPE router will be .....

A	IPv4 Address
B	IPv4 mapped IPv6 address
C	Default IP
D	None of them
E	IPv6 mapped IPv4 address

Question 20

How can we set mirror destination in Local mirroring? (Service ID= 100, SAP= 1/1/1.0) configure mirroring mirror-dest 100 sap 1/1/1.0 create no shutdown

A	configure mirroring mirror-dest 100 sap 1/1/1.0 create no shutdown
B	configure mirroring mirror-dest 100 sap 1/1/1.0 exit no shutdown
C	configure mirroring mirror-dest 100 create sap 1/1/1.0 create exit no shutdown
D	configure mirroring create mirror-dest 100 create sap 1/1/1.0 create
E	configure mirroring mirror-dest 100 create sap 1/1/1.0 no shutdown

Once you are finished, click the button below. Any items you have not completed will be marked incorrect. Get Results

There are 20 questions to complete.

gokhankosem

Gokhan Kosem is a Network Engineer, Instructor and the Founder of IPCisco.com with 15+ years of experience in Cisco, Nokia, Huawei, Juniper, Linux, Service Provider Networks, Routing and Switching technologies.

He has worked on the backbone networks of major service providers and network vendors including Nortel, Alcatel-Lucent (Nokia) and has extensive hands-on experience with Cisco, Huawei, Juniper and Nokia networking technologies.

He has trained thousands of networking students worldwide through IPCisco.com, Udemy, books, labs, quizzes, and educational content across multiple social media platforms.

IPCisco.com | Best Route to Your Dreams

NRS II Services Quiz 3

NRS II SERVICES QUIZ 3

Latest Lessons

Latest Blog Posts

WHAT YOU WILL FIND?

COURSES

SPECIALS

MEMBERSHIP