CCIE R&S Quiz 10

CCIE ENTERPRISE INFRASTRUCTURE QUIZ 10

  CONGRATULATIONS! YOU HAVE COMPLETED CCIE ENTERPRISE INFRASTRUCTURE QUIZ 10. YOU HAVE %%SCORE%% TRUE ANSWERS OUT OF %%TOTAL%% QUESTIONS. YOUR SCORE IS %%PERCENTAGE%%. %%RATING%%  
Your answers are highlighted below.
Question 1
In EIGRP, A .... is the route with the best metric to reach a destination.
A
successor
B
dr
C
feasible successor
D
reported successor
E
bdr
Question 2
How can we enter the MST Configuration on Cisco switches?
A
spanning-tree mst
B
spanning-tree mst run
C
spanning-tree mst enable
D
spanning-tree mst create
E
spanning-tree mst configuration
Question 3
Which one is True for Dot1Q?
A
Used also on access ports
B
IEEE Standard
C
Do not use Extended VLAN range
D
Inserts tag to the frame
E
Uses Native VLAN
Question 4
Which ones are Cisco QoS Congestion Avoidance features?  
A
DWRED
B
AWRED
C
CRED
D
RED
E
WRED
Question 5
How can we check OSPFv3 neighbors on a Cisco Router?
A
show ipv6 ospf protocols
B
show ospf neighbor
C
show ipv6 ospf
D
show ipv6 protocols ospf
E
show ipv6 ospf neighbor
Question 6
Mapping multiple IPv6 addresses to one IPv4 address is ...
A
Terado
B
NAT64
C
Dual Stack
D
NAT46
E
Tunneling
Question 7
How can we configure a Cisco router in OSPFv3 Area 8 Totally Stub Area? (OPSF Process Number=10)  
A
Router(config)# ipv6 ospf 10 Router(config)# area 8 stub no-summary
B
Router(config)# ipv6 router ospf 10 Router(config-router)# area 8 stub
C
Router(config)# ipv6 ospf 10 Router(config)# area 8 stub
D
Router(config)# ipv6 router ospf 10 Router(config-router)# area 8 stub no-summary
E
Router(config)# router ospf 10 Router(config-router)# area 8 stub no-summary
Question 8
With which command, we can set our area 7 as NSSA on a Cisco router?
A
area 7 stub
B
area 7 totally stub
C
area 7 nssa create
D
area 7 totally stubby
E
area 7 nssa
Question 9
The router that is closer to the source router is called .... in MPLS network.
A
Upstream Router
B
Downstream Router
C
Down Router
D
Up Router
E
None of them
Question 10
What is the name of comparing the configuration with an old version or with a similar device in troubleshooting?
A
Spot difference
B
Follow path
C
Top down
D
Bottom up
E
Divide and conquer
Question 11
Which one is the format of Solicited-node Multicast Address?
A
FF02::1:00aa:aa00/104 (aa:aaaaa=last 24 bits of IP address)
B
FF02::1:FFaa:aaaa/104 (aa:aaa=middle 16 bits of MAC address)
C
FF02::1:FFaa:aaaa/104 (aa:aaaaa=last 24 bits of IP address)
D
FF02::1:00aa:aa00/104 (aa:aaa=middle 16 bits of MAC address)
E
FF02::1:00aa:aa00/104 (aa:aaa=last 16 bits of MAC address)
Question 12
Which one consist of both IPv4 and IPv6 Multicast Address of EIGRP?
A
224.0.0.10 / FF02::A
B
224.0.0.10 / FF02::110
C
224.0.0.5 / FF02::5
D
224.0.0.6 / FF02::6
E
224.0.0.9 / FF02::9
Question 13
How can we configure local preference as 300 for AS 130 on Cisco routers?
A
Router(config-router)# bgp default preference 300
B
Router(config-router)# bgp default 300
C
Router(config)# router as 130
D
Router(config)# router bgp 130
E
Router(config-router)# bgp default local-preference 300
Question 14
If we use BPDU Guard on our topology, the ports that receive BPDU go into error-disabled mode. We can check this ports with .... command.
A
show interfaces status err-disabled
B
show interface disabled
C
show err-disabled status
D
show interface errors
E
show interfaces status
Question 15
What is the name of the Policy used on Cisco routers that defines an event and the actions to be taken when an event occurs in the router?
A
SNMP policy
B
SSM
C
Event policy
D
Security policy
E
EEM policy
Question 16
For OSPF Neighborship, which parameters must be same?
A
Timer values
B
Area ID
C
All of them
D
Subnet
E
Port Number
Question 17
Which of the following statements are True about DSCP AF11? 
A
AF1 is more likely to be dropped than AF13
B
AF13 is more likely to be dropped than AF11
C
It is also DSCP 10
D
DSCP Class 2
E
Highest priority in DSCP
Question 18
In IS-IS, there is no network command. So, IS-IS networks are added to IS-IS process under the interfaces.
A
False
B
True
Question 19
In Totally NSSA area which ones are allowed into the area?
A
LSA 7
B
Deault Route
C
LSA 4
D
LSA 5
E
LSA 3
Question 20
Which router router is responsible for forwarding multicast packets received on that network upstream to the RP in Bidirectiona PIM Operation?
A
BDR
B
AR
C
DR
D
DF
E
AVF
Question 21
Which ones of the types of Fast Reroute?
A
Path protection
B
Session protection
C
Node protection
D
Link protection
E
Network protection
Question 22
Which command enables Netflow for IP Routing under any interface of a Cisco router?
A
ip route-cache netflow
B
ip netflow enable
C
ip route flow
D
ip netflow run
E
ip route-cache flow
Question 23
To enable IP Route Profiling feature of Cisco, we use .... command.
A
ip profile run
B
ip profile create
C
ip route profile start
D
ip route profile
E
ip profile enable
Question 24
How to include network 172.16.1.0/24 under BGP process?
A
neighbor 10.10.10.0 mask 255.255.255.0
B
network 10.10.10.0 mask 255.255.255.0
C
neighbor 10.10.10.0 mask 0.0.0.255
D
network 10.10.10.0 mask 0.0.0.255
E
network 10.10.10.0 255.255.255.0
Question 25
Which messages are there in a TCP Three-Way Handsahe Mechanims?
A
FIN
B
SYN-ACK
C
FIN-ACK
D
ACK
E
SYN
Question 26
Which ones are the messages used in TCP Session Termination?
A
ACK
B
TRM
C
SYN
D
CHK
E
FIN
Question 27
How can we configure a switch with VTP Domain name MYDomain, as a VTP server and with password abc123?
A
Switch(config)# vtp MyDomain create Switch(config)# vtp server-mode Switch(config)# vtp password abc123
B
Switch(config)# vtp domain MyDomain Switch(config)# server-mode run Switch(config)# passwd abc123
C
Switch(config)# vtp-domain MyDomain Switch(config)# vtp-mode server Switch(config)# vtp-password abc123
D
Switch(config)# vtp domain MyDomain Switch(config)# vtp mode server Switch(config)# vtp password abc123
E
Switch(config)# vtp domain MyDomain Switch(config)# vtp mode-server Switch(config)# passwd abc123
Question 28
With which command can we see the neighbors's SNPA ?
A
show clns neighbors
B
show clns topology
C
show isis interface
D
show isis topology
E
show isis neighbors
Question 29
If we have an interface that has incompatible configuration, how can we add it to the EtherChannel?  (Interface = FastEthernet 0/10 , EtherChannel 2)
A
switch(config)# interface fastethernet 1/10 switch(config-if)#channel-group 2
B
switch(config)# interface fastethernet 1/10 switch(config-if)#channel-group 2 extended
C
switch(config)# interface fastethernet 1/10 switch(config-if)#set channel-group 2
D
switch(config)# interface fastethernet 1/10 switch(config-if)#channel-group 2 enable
E
switch(config)# interface fastethernet 1/10 switch(config-if)#channel-group 2 force
Question 30
Hop Count value .... is used for infinite route.
A
255
B
15
C
1
D
0
E
16
Question 31
.... is used by IPv6 devices to discover multicast group listeners.
A
MLD
B
IGMP
C
CGMP
D
PIM
E
ICMP
Question 32
How can we display information about LDP neighbor discovery on a Cisco router?
A
show ldp discovery
B
show mpls ldp discovery
C
show mpls discovery
D
show mpls ldp
E
show mpls ldp peers
Question 33
Which ones are the latest version of IGMP and MLD?
A
IGMPv3 and MLDv1
B
IGMPv2 and MLDv3
C
IGMPv3 and MLDv2
D
IGMPv2 and MLDv2
E
IGMPv3 and MLDv3
Question 34
Which EIGRP distances are considered when selecting the best route for a network?   
A
Feasible distance
B
Advertised distance
C
Topological distance
D
Successor distance
E
All of them
Question 35
Which of the following statements are True regarding MED?
A
MED is an optional nontransitive attribute.
B
MED is a routing protocol
C
Highest MED is preferred
D
Lowest MED is preferred
E
Also known as the external metric of a route
Question 36
After an IGMP Leave message received by the switch, it sends ..... if are there still any receiver for that Multicast group on that port.
A
Leave Group (v2)
B
Membership Report (v2)
C
PIM Join
D
Group-Specific Query
E
Source-Specific Query
Question 37
OSPFv3 Neighbourship is established over IPv6 Link-Local Addresses.
A
True
B
False
Question 38
In IP Multicast, to overcome UDP's unguaranteed transfer, .... is used with UDP.
A
PIM
B
ICMP
C
IGMP
D
RTP
E
TCP
Question 39
Which EIGRP distances are considered when selecting the best route for a network?   
A
Advertised distance
B
Feasible distance
C
Topological distance
D
All of them
E
Successor distance
Question 40
.... is one of the efficient solutions for connecting IPv6 networks over an IPv4 MPLS network.
A
ISATAP
B
Dual-Stack
C
6PE
D
None of them
E
Toredo
Question 41
Which ones are the correct order of BGP states?
A
open sent, openconfirm, established, idle, connect
B
idle, connect, open sent, openconfirm, established
C
idle, open sent, openconfirm, established, connect
D
open sent, openconfirm, connect, established, idle
E
open sent, openconfirm, idle, connect, established
Question 42
Default HSRP Priority is ....
A
0
B
150
C
1
D
100
E
120
Question 43
What is the global level command for setting up all the ports to use Portfast?
A
spanning-tree portfast
B
spanning-tree portfast global
C
spanning-tree portfast enable
D
spanning-tree portfast default
E
spanning-tree portfast run
Question 44
Which ones are True for RADIUS but not TACACS?
A
Uses TCP 49 port
B
Encrypt only password
C
Uses UDP 1512/1513 ports
D
Al of them
E
Developed as Cisco proprietary
Question 45
How can we deny HTTPS traffic coming from 172.16.100.0/28 to any host with an ACL? (ACL Number 130)  
A
access-list 105 deny tcp 172.16.100.0 0.0.0.15 any eq 443
B
access-list 105 permit tcp 172.16.100.0 0.0.0.15 any eq 80
C
access-list 105 permit tcp 172.16.100.0 0.0.0.15 any eq 443
D
access-list 105 permit tcp 172.16.100.0 0.0.0.15 any 80
E
access-list 105 permit tcp 172.16.100.0 0.0.0.255 any eq 443
Question 46
To enable NBAR on an interface to discover traffic for all the protocols, we use ... command on a Cisco router.
A
nbar protocol-discovery create
B
nbar-protocol discovery run
C
ip nbar protocol enable
D
nbar protocol-discovery run
E
ip nbar protocol-discovery
Question 47
Which one allows you to monitor traffic from source ports over multiple switches remotely?
A
RSPAN
B
NetFlow
C
SPAN
D
Netconf
E
Monitor
Question 48
To deactivate EIGRP Split Horizon under an IPv6 interface, we use .... command.
A
no ipv6 split-horizon
B
ipv6 split-horizon shutdown
C
no ip split-horizon eigrp
D
no ipv6 split-horizon eigrp
E
ipv6 split-horizon disable
Question 49
Which one is True for Fast Switching as Router switching mechanism?  
A
High CPU-intensive
B
Processes initial packet, then caches
C
All of them
D
Can be review by "show cpu cache"
E
Enabled with "ip route-cache" command
Question 49 Explanation: 
Less CPU-Intensive. Route cache can be reviewed using "show ip cache".
Question 50
How can we set BGP Keepalive time as 50 and Hold time as 150?
A
bgp 50 150 timers
B
set bgp 50 150 timers
C
set timers 50 150
D
timers bgp 50 150
E
bgp 50 150
Once you are finished, click the button below. Any items you have not completed will be marked incorrect. Get Results
There are 50 questions to complete.
gokhan-kosem-instructor-ipcisco

Gokhan Kosem is a Network Engineer, Instructor and the Founder of IPCisco.com with 15+ years of experience in Cisco, Nokia, Huawei, Juniper, Linux, Service Provider Networks, Routing and Switching technologies.

He has worked on the backbone networks of major service providers and network vendors including Nortel, Alcatel-Lucent (Nokia) and has extensive hands-on experience with Cisco, Huawei, Juniper and Nokia networking technologies.

He has trained thousands of networking students worldwide through IPCisco.com, Udemy, books, labs, quizzes, and educational content across multiple social media platforms.

IPCisco.com | Best Route to Your Dreams