NRS II Services Quiz 1 ⋆ IpCisco

NRS II SERVICES QUIZ 1

Please wait while the activity loads.
If this activity does not load, try refreshing your browser. Also, this page requires javascript. Please visit using a browser with javascript enabled.

If loading fails, click here to try again

CONGRATULATIONS!

YOU HAVE COMPLETED NRS II SERVICES QUIZ 1.

YOU HAVE %%SCORE%% TRUE ANSWERS OUT OF %%TOTAL%% QUESTIONS.

YOUR SCORE IS %%PERCENTAGE%%.

%%RATING%%

Your answers are highlighted below.

Question 1

Under IES service (50) configuration how can we do spoke-SDP termination with SDP 100 for VPLS 200 ? (Interface Name = ABC, IP Address = 1.1.1.0/24)

A	configure service ies interface ABC address 1.1.1.0 255.255.255.0 spoke-sdp 200:100 create
B	configure service ies interface ABC address 1.1.1.0 255.255.255.0 spoke-sdp 100:200 create
C	configure service ies 50 interface ABC address 1.1.1.0/24 spoke-sdp 200:100 create
D	configure service ies 50 interface ABC address 1.1.1.0/24 spoke-sdp 100:200 create
E	configure service 50 ies interface ABC address 1.1.1.0/24 spoke-sdp 100:200

Question 2

If we have a SAP, 1/1/1:*, what is it means?

A	Untagged frames are rejected
B	Untagged frames and tagged frames are accepted
C	Tagged frames are rejected
D	None of them
E	Untagged frames and tagged frames are rejected

Question 3

IPv4 mapped IPv6 address is produced prepending .... to the IPv4 address.

A	::FF00:
B	::FFFF:0
C	::FFFF:F:F
D	::FFFF:
E	::FFFF:0:F

Question 4

To test the connectivity of VPWS both in-band and out-of-band we use .... OAM Command.

A	VCCV-ping
B	All of them
C	LSP-ping
D	LSP-trace
E	VCCV-trace

Question 5

What is the Minimum MTU value for Access Mode and Null Encapsulation?

A	1518
B	1514
C	1510
D	1522
E	1500

Question 6

Which ones are true for SDP?

A	Services can use different encapsulations
B	An SDP is Unique in a router
C	Same SDP ID can be used in a router
D	System IP is used to define SDP
E	Many services can be in one SDP

Question 7

How can we enable mpls on interface system on Nokia routers?

A	interface system
B	enable mpls
C	configure router system
D	configure router mpls
E	mpls run

Question 8

Route Distinguisher is .... long.

A	1 Byte
B	8 Bytes
C	4 Bytes
D	2 Bytes
E	16 Bytes

Question 9

Which one is True for IES ?

A	Layer 3 Service
B	Layer 2 Service
C	Used on Access Ports
D	Uses Private IP
E	Uses Public IP

Question 10

To show only VPRN 250 Routing Table, we use .... commnad.

A	show router 250 rt
B	show service 250 routing
C	show service 250 routing-table
D	show router 250 route-table
E	show service 250 route-table

Question 11

Within the same VPN Service, Flooded traffic that come to Spoke-SDP, it sends this to

A	None of them
B	Mesh-SDPs
C	Other Spoke-SDPs
D	SAPs
E	All of them

Question 12

VPN Service ID can be manually set for each Spoke-SDP.

A	False
B	True

Question 13

SDP is unidirectional. So for VPN services, at least two SDPs are needed if you will use SDP.

A	True
B	False

Question 14

A mirror source can have multiple destinations.

A	False
B	True

Question 14 Explanation:

A mirror source can have one destination.

Question 15

To expand the VLAN space, which encapsulation mode is used?

A	Trunk
B	Dot1q
C	Access
D	Null
E	Q-in-Q

Question 16

To make IP addresses globally unique, they are converted VPN-IPv4 addresses via .... in VPRN.

A	IP Address
B	All of them
C	MAC Address
D	Route Distinguisher
E	Route Target

Question 17

How can we configure Epipe 5 for customer 10 with description xyz?

A	configure service epipe 5 customer 10 create no shutdown
B	configure service epipe 5 create description xyz no shutdown
C	configure service epipe 5 customer 10 create description xyz no shutdown
D	configure service epipe 5 customer create no shutdown
E	configure router service epipe 5 customer 10 create

Question 18

Which ones are some of the information that we can see with "show service id "service-id" base" command?

A	Service SDPs
B	Last Status Change
C	Customer ID
D	Route Preference
E	All of them

Question 19

How can we configure VPLS 100 for customer 12 with description xyz_vpls?

A	configure service vpls 100 customer 12 create description xyz_vpls no shutdown
B	configure router service vpls 100 customer 12 description xyz_vpls
C	configure service vpls 100 create description xyz_vpls no shutdown
D	configure router service vpls 100 customer 12 description xyz_vpls no shutdown
E	configure service vpls 100 create customer 12 create description xyz_vpls no shutdown

Question 20

How can we define a two hop path named MyPath from P1 to P3 witch strict definitions? (P1----P2----P3) (System IPs; P1=1.1.1.1 P2=2.2.2.2 P3=3.3.3.3)

A	configure router mpls path MyPath hop 2.2.2.2 hop 3.3.3.3
B	configure router mpls path MyPath hop 10 2.2.2.2 strict hop 20 3.3.3.3 strict no shutdown
C	configure router mpls path MyPath hop 10 2.2.2.2 strict hop 20 3.3.3.3 strict
D	configure mpls path MyPath hop 10 2.2.2.2 strict hop 20 3.3.3.3 strict
E	configure router mpls path MyPath hop 2.2.2.2 hop 3.3.3.3 no shutdown

Once you are finished, click the button below. Any items you have not completed will be marked incorrect. Get Results

There are 20 questions to complete.

NRS II Services Quiz 1

NRS II SERVICES QUIZ 1

Latest Lessons

Latest Blog Posts

WHAT YOU WILL FIND?

COURSES

SPECIALS

MEMBERSHIP