JNCIP Quiz 2 ⋆ IpCisco

JNCIP QUIZ 2

Please wait while the activity loads.
If this activity does not load, try refreshing your browser. Also, this page requires javascript. Please visit using a browser with javascript enabled.

If loading fails, click here to try again

CONGRATULATIONS!

YOU HAVE COMPLETED JNCIP QUIZ 2.

YOU HAVE %%SCORE%% TRUE ANSWERS OUT OF %%TOTAL%% QUESTIONS.

YOUR SCORE IS %%PERCENTAGE%%.

%%RATING%%

Your answers are highlighted below.

Question 1

RSVP ..... are used to send labels through upstream direction.

A	RESV Messages
B	PATH Messages
C	Notify Messages
D	Hello Messages
E	Session Messages

Question 2

LDP Hellos use .... multicast address.

A	224.0.0.1
B	224.0.0.2
C	224.0.0.13
D	224.0.0.16
E	224.0.0.22

Question 3

With ..... , the traffic is controlled and if the traffic close to the traffic exceed, it uses queues and made some of the traffic buffered without any drop action.

A	Traffic Shaping
B	Traffic Classification
C	Traffic Marking
D	Traffic Caching
E	Traffic Policing

Question 4

What is the equivalent of IPv6 address 2003:3700:0025:0000:0000:0000:0000:0005?

A	2003:3700:25::5
B	2003:37::25:0:0:0:0:5
C	2003:37::25:0000:0000:0000:0000:0005
D	2003:37:0:25:0000:0000:0000:0000:0005
E	2003:3700::25::5

Question 5

How can we configure BGP COnfederation with 67500 with members 67501 and 67502?

A	edit routing-options
B	set confederation members 67502
C	All of them
D	set confederation members 67501
E	set confederation 67500

Question 6

Which one is a IPv6 Multicat Address?

A	2001::123
B	FEC0::FF:001
C	3001::FF:FFF
D	FEC0::FF:FFF
E	FF02::5

Question 7

In Layer 3 VPN, to determine the final egress PE device for customer routes in a particular VRF, .... are used.

A	Route Distinguisher
B	VRP Tables
C	Route Targets
D	MPBGP Tables
E	ARP Records

Question 8

How can we display the aggregated interfaces on JUNOS?

A	show interfaces ae0
B	show interfaces lag
C	show interfaces link-aggregation
D	show interfaces aggregated
E	show interfaces detail

Question 9

STP .... State is the state that MAC Table is filled with the learned addresses.

A	Blocked
B	Established
C	Full
D	Learning
E	Listenning

Question 10

Multicast Routing Protocol Signalling direction is ...., and Multicast Flow direction is ....,

A	From Source to Receiver / From Receiver to Source
B	From Source to DR / From DR to Source
C	From Receiver to RP/ From RP to Receiver
D	From Source to RP / From RP to Source
E	From Receiver to Source / From Source to Receiver

Question 11

What is True for many-to-many multicast applications?

A	All of them
B	More complex than one-to-one model
C	All devices are both sources and receivers
D	Receivers are known
E	Full mesh topology is used

Question 12

To use show commands in the configuration mode, .... keyword is prepended to the show command.

A	set
B	run
C	more
D	show
E	display

Question 13

If the DR Priorities are same, according to which criteria, DR election is done in a Multicast domain?

A	Lowest IP
B	Lowest MAC
C	Lowest Cost
D	Highest IP
E	Highest MAC

Question 14

If you set your OSPF router's priority to ..., it is never selected as DR.

A	10
B	100
C	1
D	0
E	255

Question 15

How can we check the configured static routes on a Juniper router?

A	show protocol-options
B	show routing
C	show route-options
D	show routing-options
E	show routing-protocols

Question 16

In MPLS Network, At the last Edge LSR, label is removed. This process is called ....

A	php
B	push
C	none of them
D	pop
E	swap

Question 17

How can we check IS-IS interfaces?

A	show router isis brief
B	show router isis neighbors
C	show isis interface
D	show isis peers
E	show router isis interface

Question 18

There are two types RSVP-signaled LSPs. Which ones are True about them?

A	Constrained-path LSPs : Hops of LSP are computed automatically.
B	Explicit-path LSPs : Hops of the LSP are configured manually .
C	Explicit-path LSPs : Hops of LSP are computed automatically.
D	Constrained-path LSPs : Hops of the LSP are configured manually .

Question 19

How can we see our OSPF neighbors on Juniper routers?

A	show ospf peers
B	show ospf neighbor
C	show ospf details
D	show ospf peer details
E	show ospf neighbor details

Question 20

How can we check TCP connections on our Juniper router?

A	show protocol tcp
B	show system tcp
C	show protocol connections
D	show system statistics
E	show system connections

Once you are finished, click the button below. Any items you have not completed will be marked incorrect. Get Results

There are 20 questions to complete.

gokhankosem

Gokhan Kosem is a Network Engineer, Instructor and the Founder of IPCisco.com with 15+ years of experience in Cisco, Nokia, Huawei, Juniper, Linux, Service Provider Networks, Routing and Switching technologies.

He has worked on the backbone networks of major service providers and network vendors including Nortel, Alcatel-Lucent (Nokia) and has extensive hands-on experience with Cisco, Huawei, Juniper and Nokia networking technologies.

He has trained thousands of networking students worldwide through IPCisco.com, Udemy, books, labs, quizzes, and educational content across multiple social media platforms.

IPCisco.com | Best Route to Your Dreams

JNCIP Quiz 2

JNCIP QUIZ 2

Latest Lessons

Latest Blog Posts

WHAT YOU WILL FIND?

COURSES

SPECIALS

MEMBERSHIP